歡迎光臨~庫納格流體控制系統（上海）有限公司
語言選擇：
∷
∷
| 編號 | 中文名稱 | 英文名稱 | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| BS 1560-3.2-1989 | 管子、閥門和接頭(規定等級)用圓法蘭.第3部分:鋼、鑄鐵和銅合金法蘭.第2節:鑄鐵法蘭規范 | Circular flanges for pipes, valves and fittings (Class designated) - Steel, cast iron and copper alloy flanges - Specification for cast iron flanges | |||||||||
| BS 1782-1951 | 消防軟管接頭除外的吸入軟管和送水軟管接頭(1.5英寸至8英寸標稱尺寸)規范 | Specification for couplings for suction and delivery hose (11/2 in. to 8 in. nominal sizes) other than fire hose couplings | |||||||||
| BS 1906-1952 | (標稱尺寸1/8英寸-1/4英寸）軟管接頭(露天和水中使用)規范 | Specification for hose couplings (air and water) (1/8 in. to 11/4 in. nominal sizes) | |||||||||
| BS 2051-1-1973 | 工程用管與管接頭規范.第1部分:工程用銅與銅合金毛細管與耐壓管接頭 | Tube and pipe fittings for engineering purposes - Copper and copper alloys capillary and compression tube fittings for engineering purposes | |||||||||
| BS 2051-2-1984 | 工程用管與管接頭規范.第2部分:橄欖型銅合金耐壓管接頭 | Tube and pipe fittings for engineering purposes - Specification for olive type copper alloy compression tube fittings | |||||||||
| BS 2464-1954 | 汽油、石油和潤滑劑用軟管接頭(標稱尺寸 1/4英寸至 4英寸)規范 | Specification for hose couplings for petrol, oil and lubricants (3/4 in. to 4 in. nominal sizes) | |||||||||
| BS 2464-2-1969 | 石油、汽油和潤滑油用軟管接頭規范.第2部分:高壓接頭 | Specification for hose couplings for petrol, oil and lubricants - High pressure couplings | |||||||||
| BS 2464-3-1968 | 汽油、石油和潤滑劑用軟管接頭規范.第3部分:快速接頭 | Specification for hose couplings for petrol, oil and lubricants - Quick-acting couplings | |||||||||
| BS 2464-4-1980 | 汽油、石油和潤滑劑用軟管接頭規范.第4部分:歐洲型 100mm快速接頭規范 | Hose couplings for petrol, oil and lubricants - Specification for 100 mm quick-acting couplings: European type | |||||||||
| BS 2761-1983 | 球面接頭規范 | Specification for spherical ground joints | |||||||||
| BS 2782-11 Method 1108A-1989 | 塑料試驗方法.第11部分:熱塑性塑料管、接頭和閥門.試驗方法1108A:管界面限定碰撞率 | Methods of testing plastics - Thermoplastics pipes, fittings and valves - True impact rate (TIR) boundaries of pipes | |||||||||
| BS 2782-11 Method 1109A-1989 | 塑料試驗方法.第11部分:熱塑性塑料、接頭和閥門.試驗方法1109A:非承壓聚乙烯管和接頭耐壞境應力開裂性 | Methods of testing plastics - Thermoplastics pipes, fittings and valves - Resistance to environmental stress cracking of polyethylene pipes and fittings for non-pressure applications | |||||||||
| BS 2782-11 Method 1121B-1997 | 塑料的試驗方法.第11部分:熱塑管、接頭和閥門.流體輸送用熱塑管.試驗方法1121B:額定外部直徑和額定壓力.米 | Methods of testing plastics - Thermoplastics pipes, fittings and valves - Thermoplastics pipes for the conveyance of fluids - Nominal outside diameters and nominal pressures - Metric series | |||||||||
| BS 2782-11 Method 1121C-1997 | 塑料試驗方法.第11部分:熱塑管、接頭和閥門.流體輸送用熱塑管.試驗方法1121C:額定外部直徑和額定壓力.英尺 | Methods of testing plastics - Thermoplastics pipes, fittings and valves - Thermoplastics pipes for the conveyance of fluids - Nominal outside diameters and nominal pressures - Inch-based series | |||||||||
| BS 2782-11 Method 1121H-1996 | 塑料試驗方法.第11部分:熱塑性塑料管、接頭和閥門.試驗方法1121H:非承壓液體輸送熱塑性塑料管.管頭損失計算 | Methods of testing plastics - Thermoplastics pipes, fittings and valves - Thermoplastics pipes for the transport of liquids under pressure - Calculation of head losses | |||||||||
| BS 2C 4-1973 | 飛機發動機制冷劑壓力灌注接頭尺寸規范 | Specification for coupling dimensions for aero-engine refrigerant pressure replenishment connections | |||||||||
| BS 2C 5-1976 | 液氧灌注連接頭配合尺寸規范 | Specification for mating dimensions for liquid oxygen replenishment couplings | |||||||||
| BS 2M 53-1997 | 飛機.液壓系統.管道和管接頭熱沖擊試驗 | Aircraft - Fluid systems - Thermal shock testing of piping and fittings | |||||||||
| BS 2SP 101-104-1956 | 飛行器用旋轉套筒、張力傳動桿和旋壓鋼索端部接頭(統一螺紋)規范 | Specifications for turnbarrels, tension rods and swaged cable-end connections (Unified threads) for aircraft | |||||||||
| BS 2SP 7-1943 | 飛機材料規范.叉形接頭(高強度型)(尺寸號 4B.A.至<1/4>英寸B.S.F | Specification for aircraft material - Fork joints (high tensile type) (for sizes No. 4 B.A. to 3/4 inch B.S.F. inclusive) | |||||||||
| BS 31-1940 | 電氣布線用鋼導線管和管接頭 | Specification - Steel conduit and fittings for electrical wiring | |||||||||
| BS 3288-3-1989 | 架空電力導線絕緣和導線接頭.第3部分:絕緣子組件球窩連接接頭尺寸 | Insulator and conductor fittings for overhead power lines - Dimensions of ball and socket couplings of string insulator units | |||||||||
| BS 336-1989 | 消防軟管接頭與輔助設備的規范 | Specification for fire hose couplings and ancillary equipment | |||||||||
| BS 341-3-2002 | 可運輸氣體容器的閥門.閥門出口接頭 | Transportable gas container valves - Valve outlet connections | |||||||||
| BS 3799-1974 | 石油工業用鋼管配件、螺旋管接頭和套管焊接規范 | Specification for steel pipe fittings, screwed and socket-welding for the petroleum industry | |||||||||
| BS 3818-1964 | 柴油機車及有軌內燃機車自動密封加油接頭規范 | Specification for self-sealing fuelling couplings for diesel locomotives and diesel railcars | |||||||||
| BS 3SP 3-1943 | 飛機材料規范.叉形接頭(低強度型)(尺寸自N0.4B.A至<1/2>英寸B.S.F.) | Specification for aircraft material - Fork joints (low tensile type) (for sizes No. 4 B.A. to 1/2 inch B.S.F. inclusive) | |||||||||
| BS 4222-1967 | 牙科手持機的傳動聯軸器(滑配接頭)尺寸規范 | Specification for dimensions of the transmission coupling (slip-joint) to dental handpieces | |||||||||
| BS 4368-4-1984 | 液壓和通用壓合管接頭.第4部分:型號試驗要求規范 | Metallic tube connectors for fluid power and general use - Specification for type test requirements | |||||||||
| BS 4568-1-1970 | 電氣裝置用ISO型米制螺紋鋼導管及接頭規范.第1部分:鋼導管、彎頭和接頭 | Specification for steel conduit and fittings with metric threads of ISO form for electrical installations - Steel conduit, bends and couplers | |||||||||
| BS 4579-2-1973 | 電纜和電線連接器機械和壓合接頭性能規范.第2部分:鎳、鐵及鍍銅導線壓合接頭 | Specification for performance of mechanical and compression joints in electric cable and wire connectors - Compression joints in nickel, iron and plated copper conductors | |||||||||
| BS 4607-1-1984 | 電氣裝置用非金屬導管及接頭規范.第1部分:絕緣材料接頭和元件規范 | Non-metallic conduits and fittings for electrical installations - Specification for fittings and components of insulating material | |||||||||
| BS 4607-5-1982 | 電氣裝置用非金屬導管及接頭規范.第5部分:絕緣材料剛性導管、接頭和元件規范 | Non-metallic conduits and fittings for electrical installations - Specification for rigid conduits, fittings and components of insulating material | |||||||||
| BS 4622-1970 | 灰口鐵管和管接頭規范 | Specification for grey iron pipes and fittings | |||||||||
| BS 4742-4-1985 | 農用機械液壓設備.第4部分:掛車和機具用制動系統用液壓管接頭規范 | Hydraulic equipment for agricultural machinery - Specification for hydraulic couplings on braking systems for trailers and trailed equipment | |||||||||
| BS 4742-7-1989 | 農用機械液壓設備.第7部分:農用拖掛車輛液壓制動系統管接頭用油口連接規范 | Hydraulic equipment for agricultural machinery - Specification for port connections for agricultural trailed vehicle hydraulic brake couplings | |||||||||
| BS 4871-3-1985 | 按認可焊接工藝操作的焊工鑒定考試規范.第3部分:金屬管與管板接頭間電弧焊 | Specification for approval testing of welders working to approved welding procedures - Arc welding of tube to tube-plate joints in metallic materials | |||||||||
| BS 4G 178-2-1986 | 飛機電纜電線壓接頭.第2部分:壓接檢驗規范(包括用戶檢驗試驗) | Crimped joints for aircraft electrical cables and wires - Specification for control of crimping (including user control tests) | |||||||||
| BS 5200-1997 | 水管接頭和轉接器的尺寸規范 | Specification for dimensions of hydraulic connectors and adaptors | |||||||||
| BS 534-1990 | 水和污水用鋼管接頭和異型管件規范 | Specification for steel pipes, joints and specials for water and sewage | |||||||||
| BS 5529-1988 | 工業用低壓開關設備和控制裝置規范.A型、直流用、3或4個接頭的近距離電感開關 | Specification for low-voltage switchgear and controlgear for industrial use - Inductive proximity switches - Form A, for direct current, 3 or 4 terminals | |||||||||
| BS 5611-1978 | 負載分接頭切換開關應用指南 | Application guide for on-load tap-changers | |||||||||
| BS 5649-5-1982 | 路燈桿規范.第5部分:電氣接頭底座與電線敷設槽規范 | Lighting columns - Specification for base compartments and cableways | |||||||||
| BS 572-1985 | 互換式錐形毛玻璃接頭規范 | Specification for interchangeable conical ground glass joints | |||||||||
| BS 5911-1-2002 | 預制混凝土管、管配件和輔助制品.具有軟接頭的非加筋、加筋混凝土管(包括套管)和管配件規范(對 BS EN 1916: | Concrete pipes and ancillary concrete products - Specification for unreinforced and reinforced concrete pipes (including jacking pipes) and fittings with flexible joints(comnplementary to BSEN 1916:2002) | |||||||||
| BS 5911-5-2004 | 混凝土管和輔助混凝土制品.帶軟接頭的預應力非壓力管道和配件的規范 | Concrete pipes and ancillary concrete products - Specification for prestressed non-pressure pipes and fittings with flexible joints | |||||||||
| BS 6083-5-1984 | 助聽器.第5部分:內插式耳機短接管接頭和封閉裝置尺寸規范 | Hearing aids - Specification for dimensions of the nipple and sealing device for insert earphones | |||||||||
| BS 6102-15-1991 | 自行車.第15部分:輻條螺紋接頭尺寸規范 | Cycles - Specification for dimensions of spoke nipples | |||||||||
| BS 6362-1990 | 按BS21 "帶壓密接合螺紋接頭的管及配件管螺紋" 攻絲的不銹鋼管規范 | Specification for stainless steel tubes suitable for screwing in accordance with BS 21 'Pipe threads for tubes and fittings where pressure-tight joints are made on the threads' | |||||||||
| BS 6464-1984 | 制煉廠用增強塑料管、配件和接頭規范 | Specification for reinforced plastics pipes, fittings and joints for process plants | |||||||||
| BS 65-1991 | 只用于地表水管道和配件的陶管、配件、導管和撓性機械接頭規范 | Specification for vitrified clay pipes, fittings and ducts, also flexible mechanical joints for use solely with surface water pipes and fittings | |||||||||
| BS 6537-1984 | 液壓流體設備用U型接頭規范 | Specification for staple type connectors for hydraulic fluid power applications | |||||||||
| BS 669-1-1989 | 燃氣灶具用軟管、管接頭和承窩接口.第1部分:采用第1、2類燃氣的家用灶具用帶繞金屬軟管、護罩、接頭配件和 | Flexible hoses, end fittings and sockets for gas burning appliances - Specification for strip-wound metallic flexible hoses, covers, end fittings and sockets for domestic appliances burning 1st and 2nd family gases | |||||||||
| BS 669-2-1997 | 燃氣灶具用軟管、接頭和管座.使用第1、2和3類燃氣的家用灶具波紋金屬軟管、封蓋、接頭和管座規范 | Flexible hoses, end fittings and sockets for gas burning appliances - Specification for corrugated metallic flexible hoses, covers, end fittings and sockets for catering appliances burning 1st, 2nd and 3rd family gases | |||||||||
| BS 6910-2-1989 | 電壓范圍為交流1000V和直流1500Vd.c.的低溫澆注樹脂復合物和熱縮電纜接頭.第2部分:現場安裝實用規程 | Cold pour resin compound and heat-shrink cable joints in the voltage range up to 1000 V a.c. and 1500 V d.c. Code of practice for on-site installation | |||||||||
| BS 746-2005+A1-2009 | 燃氣表活接頭與轉接器用規范 | Specification for gas meter unions and adaptors | |||||||||
| BS 7677-1993 | 管道接頭用密封圈缺陷分類推薦標準 | Recommendations for classification of imperfections in pipe joint rings | |||||||||
| BS 778-1966 | 液壓用鋼管與接頭規范 | Specification for steel pipes and joints for hydraulic purposes | |||||||||
| BS 8407-2002 | 地下用輸送帶機械和疊接接頭的規范 | Specification for mechanical and spliced joints in conveyor belting for use underground | |||||||||
| BS 864-2-1983 | 銅和銅合金制毛細管與承壓管配件.銅管用毛細管與壓合接頭規范 | Capillary and compression tube fittings of copper and copper alloy. Specification for capillary and compression fittings for copper tubes | |||||||||
| BS 9522 N0001-1982 | 直流和低頻用多觸頭圓形電氣連接件詳細規范、帶有前面可釋放后面可拆卸的壓接觸點卡口接頭.全面評估級 | Detail specification for multi-contact circular electrical connectors for d.c. and low frequency applications - Bayonet coupling with front release, rear removable crimp contacts - Full assessment level | |||||||||
| BS 9522 N0003-1990 | 直流和低頻用多觸點圓形電氣連接器詳細規范.帶后可插入、后釋放、后可拆卸壓接觸點的無檔板密封、耐環境影 | Detail specification for multi-contact circular electrical connectors for d.c. and low frequency applications - Bayonet coupling non-barrier sealed, environment resistant with rear insertable, rear release, rear removable crimp contacts also barrier sealed with non-removable solder contact styles - Full plus airframe fit assessment | |||||||||
| BS A 358-3-2000 | MJ螺紋.流體系統用的接頭的極限尺寸 | MJ threads - Limit dimensions for fittings for fluid systems | |||||||||
| BS AU 91-1965 | 起動蓄電池圓錐形接線端子的電纜接頭尺寸(用正極接地部件的汽車和輕便商用汽車)規范 | Specification for dimensions of electrical cable connectors for starter battery taper terminal posts (cars and light commercial vehicles using positive earth system) | |||||||||
| BS DD CEN/TS 1591-3-2007 | 法蘭及其連接件.墊圈的圓形法蘭連接件用設計原則.第3部分:金屬與金屬接點之間的法蘭接頭的計算方法 | Flanges and their joints - Design rules for gasketed circular flange connections - Part 3: Calculation method for metal to metal contact type flanged joint | |||||||||
| BS DD CEN/TS 1591-4-2007 | 法蘭及其連接件.墊圈的圓形法蘭連接件用設計原則.第4部分:服從壓力設備指令、符合設備螺栓接頭裝配要求的人 | Flanges and their joints — Design rules for gasketed circular flange connections — Part 4: Qualification of personnel competency in the assembly of bolted joints fitted to equipment subject to the Pressure Equipment Directive | |||||||||
| BS EN 10253-1-1999 | 對接焊管道接頭.通用和無特殊檢驗要求的鍛制碳鋼 | Butt-welding pipe fittings - Wrought carbon steel for general use and without specific inspection requirements | |||||||||
| BS EN 10253-2-2007 | 對接焊管道接頭.帶特殊檢驗要求的非合金和鐵素體合金鋼 | Butt-welding pipe fittings — Part 2: Non alloy and ferritic alloy steels with specific inspection requirements | |||||||||
| BS EN 10253-3-2008 | 對焊管接頭.無特殊檢驗要求的鍛制奧氏體和奧氏體-鐵素體(二相)不銹鋼 | Butt-welding pipe fittings - Part 3: Wrought austenitic and austenitic-ferritic (duplex) stainless steels without specific inspection requirements | |||||||||
| BS EN 10253-4-2008 | 對焊管道接頭.具有特殊檢驗要求的鍛制奧氏體和鐵素體－奧氏體(二相)不銹鋼 | Butt-welding pipe fittings - Part 4:Wrought austenitic and austenitic-ferritic (duplex) stainless steels with specific inspection requirements | |||||||||
| BS EN 10311-2005 | 水和其他含水液體傳送用鋼管和配件的連接用接頭 | Joints for the connection of steel tubes and fittings for the conveyance of water and other aqueous liquids | |||||||||
| BS EN 1075-2000 | 木結構.試驗方法.由沖打孔金屬板緊固件構成的接頭 | Timber structures - Test methods - Joints made with punched metal plate fasteners | |||||||||
| BS EN 1092-2-1997 | 法蘭及其連接.按PN標注的管、閥門、管接頭和附件的圓形安裝法蘭.第2部分:鑄鐵法蘭 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Cast iron flanges | |||||||||
| BS EN 12308-1998 | 液化天然氣設施和設備.用于液化天然氣管道的法蘭接頭墊圈設計適配性試驗 | Installations and equipment for LNG - Suitability testing of gaskets designed for flanged joints used on LNG piping | |||||||||
| BS EN 12316-1-2000 | 防水柔性板.接頭抗剝離性的測定.屋頂防水瀝青板 | Flexible sheets for waterproofing - Determination of peel resistance of joints - Bitumen sheets for roof waterproofing | |||||||||
| BS EN 12316-2-2000 | 防水柔性板.接頭抗剝離性的測定.屋頂防水用塑料和橡膠薄板 | Flexible sheets for waterproofing - Determination of peel resistance of joints - Plastic and rubber sheets for roof waterproofing | |||||||||
| BS EN 12317-1-2000 | 防水柔性板.屋頂防水瀝青板.接頭抗剪切性的測定 | Flexible sheets for waterproofing - Bitumen sheets for roof waterproofing - Determination of shear resistance of joints | |||||||||
| BS EN 12512-2001 | 木結構.試驗方法.機械緊固件接頭的周期測試 | Timber structures - Test methods - Cyclic testing of joints made with mechanical fasteners | |||||||||
| BS EN 12517-2-2008 | 焊縫的無損檢驗.通過射線照相術評估鋁及鋁合金的焊接接頭.驗收等級 | Non-destructive testing of welds - Part 2: Evaluation of welded joints in aluminium and its alloys by radiography - Acceptance levels | |||||||||
| BS EN 1254-1-1998 | 銅和銅合金.管路接頭.銅管毛細管釬焊法或銅焊法用端頭接頭 | Copper and copper alloys - Plumbing fittings - Fittings with ends for capillary soldering or capillary brazing to copper tubes | |||||||||
| BS EN 1254-2-1998 | 銅和銅合金.管路接頭.與銅管一起使用的壓合接頭 | Copper and copper alloys - Plumbing fittings - Fittings with compression ends for use with copper tubes | |||||||||
| BS EN 1254-3-1998 | 銅和銅合金.管路接頭.與塑料管一起使用的壓合接頭 | Copper and copper alloys - Plumbing fittings - Fittings with compression ends for use with plastics pipes | |||||||||
| BS EN 1254-4-1998 | 銅和銅合金.管路接頭.與帶有毛細管或壓力端頭的其它端頭連接的管接頭 | Copper and copper alloys - Plumbing fittings - Fittings combining other end connections with capillary or compression ends | |||||||||
| BS EN 1254-5-1998 | 銅和銅合金.管路接頭.銅管毛細管銅焊法用短端頭接頭 | Copper and copper alloys - Plumbing fittings - Fittings with short ends for capillary brazing to copper tubes | |||||||||
| BS EN 12560-1-2001 | 法蘭及其接頭.標示等級的法蘭襯墊.有或無插孔的非金屬水平襯墊 | Flanges and their joints - Gaskets for Class-designated flanges - Non-metallic flat gaskets with or without inserts | |||||||||
| BS EN 12560-2-2001 | 法蘭及其接頭.標示等級的法蘭襯墊.鋼法蘭用螺旋纏繞襯墊 | Flanges and their joints - Gaskets for Class-designated flanges - Spiral wound gaskets for use with steel flanges | |||||||||
| BS EN 12560-3-2001 | 法蘭及其接頭.標示等級的法蘭襯墊.非金屬PTFE外殼襯墊 | Flanges and their joints - Gaskets for Class-designated flanges - Non-metallic PTFE envelope gaskets | |||||||||
| BS EN 12560-4-2001 | 法蘭及其接頭.標示等級的法蘭的襯墊.鋼法蘭用波紋狀、水平或皺縮金屬和填充金屬襯墊 | Flanges and their joints - Gaskets for Class-designated flanges - Corrugated, flat or grooved metallic and filled metallic gaskets for use with steel flanges | |||||||||
| BS EN 12560-5-2001 | 法蘭及其接頭.標示等級的法蘭的襯墊.鋼法蘭用金屬環接頭襯墊 | Flanges and their joints - Gaskets for Class-designated flanges - Metallic ring joint gaskets for use with steel flanges | |||||||||
| BS EN 12560-7-2004 | 法蘭及其接頭.分級標示法蘭用墊圈.鋼法蘭用涂覆金屬的套層墊圈 | Flanges and their joints - Gaskets for class-designated flanges - Covered metal jacketed gaskets for use with steel flanges | |||||||||
| BS EN 12573-4-2000 | 焊接非靜壓熱塑罐.法蘭接頭的設計和計算 | Welded static non-pressurized thermoplastic tanks - Design and calculation of flanged joints | |||||||||
| BS EN 1277-2004 | 塑料管道系統.地下無壓用熱塑性管道系統.彈性密封環型接頭密封性的試驗方法 | Plastics piping systems - Thermoplastics piping systems for buried non-pressure applications - Test methods for leaktightness of elastomeric sealing ring type joints | |||||||||
| BS EN 12797-2000 | 銅焊.銅焊接頭破壞試驗 | Brazing - Destructive tests of brazed joints | |||||||||
| BS EN 12799-2000 | 銅焊.銅焊接頭無損檢驗 | Brazing - Non-destructive examination of brazed joints | |||||||||
| BS EN 12814-1-2000 | 熱塑性半成品焊接接頭試驗.彎曲試驗 | Testing of welded joints of thermoplastics semi-finished products - Bend test | |||||||||
| BS EN 12814-2-2000 | 熱塑半成品焊接接頭試驗.拉伸試驗 | Testing of welded joints of thermoplastics semi-finished products - Tensile test | |||||||||
| BS EN 12814-3-2000 | 熱塑半成品焊接接頭試驗.拉伸蠕變試驗 | Testing of welded joints of thermoplastics semi-finished products - Tensile creep test | |||||||||
| BS EN 12814-4-2001 | 熱塑半成品焊接接頭試驗.剝離試驗 | Testing of welded joints of thermoplastics semi-finished products - Peel test | |||||||||
| BS EN 12814-5-2000 | 熱塑半成品焊接接頭試驗.宏觀檢查 | Testing of welded joints of thermoplastics semi-finished products - Macroscopic examination | |||||||||
| BS EN 12814-6-2000 | 熱塑半成品焊接接頭試驗.低溫拉伸試驗 | Testing of welded joints of thermoplastics semi-finished products - Low temperature tensile test | |||||||||
| BS EN 12814-7-2002 | 熱塑性半成品的焊接接頭的試驗.腰形試驗樣品的拉伸試驗 | Testing of welded joints of thermoplastics semi-finished products - Tensile test with waisted test specimens | |||||||||
| BS EN 12814-8-2001 | 熱塑半成品焊接接頭試驗.要求 | Testing of welded joints of thermoplastic semi-finished products -. Requirements | |||||||||
| BS EN 13090-2000 | 建筑物內氣體管道的螺紋接頭重新密封方法 | Means for resealing threaded joints of gas pipework in buildings | |||||||||
| BS EN 13100-1-2000 | 熱塑性半成品焊接接頭無損檢驗.目視檢查 | Non destructive testing of welded joints of thermoplastics semi-finished products - Visual examination | |||||||||
| BS EN 13100-2-2004 | 熱塑性半成品焊接接頭的無損檢驗.X射線照相檢驗 | Non destrictive testing of welded joints of thermoplastics semi-finished products - X-ray radiographic testing | |||||||||
| BS EN 13100-3-2004 | 熱塑性半成品焊接接頭的無損檢驗.超聲檢驗 | Non-destructive testing of welded joints in thermoplastics semi-finished products - Ultrasonic testing | |||||||||
| BS EN 13271-2002 | 木材緊固件.連接器接頭的特征載荷能力和滑脫系數 | Timber fasteners - Characteristic load-carrying capacities and slip-moduli for connector joints | |||||||||
| BS EN 14257-2006 | 粘合劑.木材粘合劑.溫度升高時搭接接頭拉伸強度的測定(WATT '91) | Adhesives - Wood adhesives - Determination of tensile strength of lap joints at elevated temperature (WATT '91) | |||||||||
| BS EN 14258-2004 | 結構粘合劑.短期或長期暴露于特定溫度條件下的粘合接頭的機械性能 | Structural adhesives - Mechanical behaviour of bonded joints subjected to short and long terms exposure at specified conditions of temperature | |||||||||
| BS EN 1435-1997 | 焊縫的無損檢驗.焊接接頭的放射性檢驗 | Non-destructive examination of welds - Radiographic examination of welded joints | |||||||||
| BS EN 144-3-2003 | 呼吸保護裝置.氣瓶閥.潛水用Nitrox和氧氣氣瓶的出口接頭 | Respiratory protective devices - Gas cylinder valves - Outlet connections for diving gases Nitrox and oxygen | |||||||||
| BS EN 14454-2005 | 防飲用水回流污染的裝置.軟管接頭防回流裝置DN 15～DN 32.A型H系列 | Devices to prevent pollution by backflow of potable water - Hose union backflow preventer DN 15 to DN 32 inclusive - Family H, type A | |||||||||
| BS EN 14525-2005 | 不同材料管道用球墨鑄鐵大公差聯接器和法蘭接頭:球墨鑄鐵、灰鑄鐵、鋼、PVC-U、PE和纖維水泥 | Ductile iron wide tolerance couplings and flange adaptors for use with pipes of different materials: ductile iron, grey iron, steel, PVC-U, PE, fibre-cement | |||||||||
| BS EN 14741-2006 | 熱塑管和管道系統.非壓力掩埋用接頭.通過評估密封壓力測定彈性密封件接合處的長期密封性能的試驗方法 | Thermoplastics piping and ducting systems - Joints for buried non-pressure applications - Test method for the long-term sealing performance of joints with elastomeric seals by estimating the sealing pressure | |||||||||
| BS EN 15096-2008 | 防飲用水回流污染用裝置.軟管接頭防真空閥.包括B型和D型H系列的DN 15～DN 25.通用技術規范 | Devices to prevent pollution by backflow of potable water - Hose Union anti-vacuum valves - DN 15 to DN 25 inclusive Family H, type B and type D. General technical specification | |||||||||
| BS EN 1515-1-2000 | 法蘭及其接頭.螺栓連接.螺栓連接的選擇 | Flanges and their joints - Bolting - Selection of bolting | |||||||||
| BS EN 15617-2009 | 焊接接頭的無損檢驗.飛行時間衍射技術(TOFD).接受等級 | Non-destructive testing of welds - Time-of-flight diffraction technique (TOFD) - Acceptance levels | |||||||||
| BS EN 1591-2-2008 | 法蘭及其接頭.帶襯墊的環形法蘭連接件的設計規則.墊圈參數 | Flanges and their joints - Design rules for gasketed circular flange connections - Part 2:Gasket parameters | |||||||||
| BS EN 1741-1998 | 帶有開放結構的蒸氣加氣混凝土或輕集料混凝土預制構件之間接頭處非平面方向抗剪切強度的測定 | Determination of shear strength for out-of-plane forces of joints between prefabricated components made of autoclaved aerated concrete or lightweight aggregate concrete with open structure | |||||||||
| BS EN 175201-804-2000 | 電子元器件質量評定協調系統.詳細規范.環形連接器.螺紋接頭直徑1.6mm圓觸點 | Harmonized system of quality assessment for electronic components - Detail specification - Circular connectors - Round contacts, size diameter 1,6 mm, threaded coupling | |||||||||
| BS EN 1829-2-2008 | 高壓噴水機器.安全要求.軟管、軟管管路和接頭 | High-pressure water jet machines — Safety requirements — Part 2: Hoses, hose lines and connectors | |||||||||
| BS EN 1993-1-8-2005 | 歐洲法規3.鋼結構的設計.接頭設計 | Eurocode 3: Design of steel structures - Part 1-8: Design of joints | |||||||||
| BS EN 205-2003 | 膠粘劑.非結構用木材粘結劑.搭接接頭拉力剪切強度的測量 | Adhesives - Wood adhesives for non-structural applications - Determination of tensile shear strength of lap joints | |||||||||
| BS EN 21089-1992 | 點焊設備用電極錐度接頭.尺寸 | Electrode taper fits for spot welding equipment - Dimensions | |||||||||
| BS EN 2591-217-2002 | 電氣和光學連接元件.試驗方法.終端接線片和連機拼合接頭在規定電流下的電壓降 | Elements of electrical and optical connection - Test methods - Voltage drop under specified current for terminal lugs and in-line splices | |||||||||
| BS EN 2591-218-2002 | 電氣和光學連接元件.試驗方法.用溫度和電流循環法試驗終端接線片和連機拼合接頭的衰老程度 | Elements of electrical and optical connection - Test methods - Ageing of terminal lugs and in-line splices by temperature and current cycling | |||||||||
| BS EN 2591-219-2002 | 電器和光學連接元件.試驗方法.絕緣終端接線片和連機拼合接頭的電壓強度 | Elements of electrical and optical connection - Test methods - Voltage strength for insulated terminal lugs and in-line splices | |||||||||
| BS EN 2591-220-2005 | 航空航天系列.電和光學連接元件.試驗方法.電流和溫度周期性變化引起的觸點/導體接頭老化 | Elements of electrical and optical connection — Test methods — Part 220: Contact/conductor joint ageing by current and temperature cycling | |||||||||
| BS EN 2665-003-1999 | 額定電流為20A至50A的溫度補償?shù)娜龢O電路斷路器.米制螺紋接頭.產品標準 | Circuit breakers, three-pole, temperature compensated, rated currents 20 A to 50 A. Metric thread terminals - Product standard | |||||||||
| BS EN 2665-004-1999 | 額定電流為20A至50A的溫度補償?shù)娜龢O電路斷路器.UNC螺紋接頭.產品標準 | Circuit breakers, three-pole, temperature compensated, rated currents 20 A to 50 A. UNC thread terminals - Product standard | |||||||||
| BS EN 26891-1991 | 木結構.機械緊固件接頭.強度和變形特性測定一般原則 | Timber structures - Joints made with mechanical fasteners - General principles for the determination of strength and deformation characteristics | |||||||||
| BS EN 2794-003-1999 | 額定電流為20A至50A的溫度補償?shù)膯螛O電路斷路器.米制螺紋接頭.產品標準 | Circuit breakers, single-pole, temperature compensated, rated currents 20 A to 50 A. Metric thread terminals - Product standard | |||||||||
| BS EN 2794-004-1999 | 額定電流為20A至50A的溫度補償?shù)膯螛O電路斷路器.UNC螺紋接頭.產品標準 | Circuit breakers, single-pole, temperature compensated, rated currents 20 A to 50 A. UNC thread terminals - Product standard | |||||||||
| BS EN 28430-1-1992 | 點焊設備規程.電極夾具.第1部分:錐形接頭錐度1:10 | Specification for resistance spot welding - Electrode holders - Taper fixing 1:10 | |||||||||
| BS EN 28430-2-1992 | 點焊設備規程.電極夾具.第2部分:莫氏錐形接頭 | Specification for resistance spot welding - Electrode holders - Morse taper fixing | |||||||||
| BS EN 28970-1991 | 木結構.用機械緊固件連接的接頭試驗.木材致密度要求 | Timber structures - Testing of joints made with mechanical fasteners - Requirements for wood density | |||||||||
| BS EN 295-1-1991 | 排水管和下水道用陶管和管配件及管接頭.要求 | Vitrified clay pipes and fittings and pipe joints for drains and sewers - Requirements | |||||||||
| BS EN 295-2-1991 | 排水管和下水道用陶管和管配件及管接頭.質量控制和抽樣 | Vitrified clay pipes and fittings and pipe joints for drains and sewers - Quality control and sampling | |||||||||
| BS EN 295-3-1991 | 排水管和下水道用陶管和管配件及管接頭.試驗方法 | Vitrified clay pipes and fittings and pipe joints for drains and sewers - Test methods | |||||||||
| BS EN 295-4-1995 | 排水管和下水道用陶制管和管配件及管接頭.專用配件、管接頭和配套附件的要求 | Vitrified clay pipes and fittings and pipe joints for drains and sewers - Requirements for special fittings, adaptors and compatible accessories | |||||||||
| BS EN 295-5-1994 | 排水管和下水道用陶管和管配件及管接頭.帶孔的陶管及配件的要求 | Vitrified clay pipes and fittings and pipe joints for drains and sewers - Requirements for perforated vitrified clay pipes and fittings | |||||||||
| BS EN 295-6-1996 | 排水管和污水管用陶制管、管件及管接頭.陶制管人孔的要求 | Vitrified clay pipes and fittings and pipe joints for drains and sewers - Requirements for vitrified clay manholes | |||||||||
| BS EN 295-7-1996 | 排水管和污水管用陶制管、管件及管接頭.陶制管和管插接接頭的要求 | Vitrified clay pipes and fittings and pipe joints for drains and sewers - Requirements for vitrified clay pipes and joints for pipe jacking | |||||||||
| BS EN 3079-2006 | 8°30'壓力＜28000kPa的導管接頭.適配器.米制系列.技術規范 | Pipe coupling 8 °30' up to 28000 kPa - Adaptors - Metric series - Technical specification | |||||||||
| BS EN 3082-2001 | 航空航天系列.鈦合金管連接件8°30'.修理用悶頭焊接活接頭 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Unions, bulkhead welded, for repair | |||||||||
| BS EN 3083-2001 | 航空航天系列.鈦合金管連接件8°30'.修理用悶頭長焊接端頭活接頭 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Unions, bulkhead, long welded end, for repair | |||||||||
| BS EN 3084-2001 | 航空航天系列.鈦合金管連接件8°30'.修理用焊接端頭螺紋活接頭 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Unions, welded end threaded for repair | |||||||||
| BS EN 3244-2001 | 航空航天系列.鈦合金8°30’管連接件.雙端頭的活接頭 | Aerospace Series - Pipe coupling 8 °30' in titanium alloy - Unions, double ended | |||||||||
| BS EN 3245-2001 | 航空航天系列.鈦合金8°30'管連接件.變徑活接頭 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Unions, reducer | |||||||||
| BS EN 3246-2001 | 航空航天系列.鈦合金8°30' 管連接件.、悶頭活接頭 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Unions, bulkhead | |||||||||
| BS EN 3247-2001 | 航空航天系列.鈦合金8°30'管連接件.悶頭焊接端活接頭、 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Unions, bulkhead welded end | |||||||||
| BS EN 3248-2001 | 航空航天系列.鈦合金管連接件8°30’.帶鎖緊裝置的縮徑管端的轉接頭 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Adaptors, reduced pipe end, with lockring | |||||||||
| BS EN 3373-001-2007 | 航空航天系列.電導體壓接用終端盒和內嵌式接頭.第001部分:技術規范 | Aerospace series — Terminal lugs and in-line splices for crimping on electric conductors — Part 001: Technical specification | |||||||||
| BS EN 3373-010-2009 | 航空航天系列.電導體壓接用終端盒和內嵌式接頭.米制和英制螺栓系列用溫度低于150℃銅導體壓接用鍍錫環型終 | Aerospace series - Terminal lugs and in-line splices for crimping on electric conductors - Terminal lugs, ring shaped, tin plated, for crimping on copper conductors, temperature up to 150 °C for metric and inch stud series - Product standard | |||||||||
| BS EN 3373-011-2009 | 航空航天系列.電導體壓接用終端盒和內嵌式接頭.米制和英制螺柱系列用溫度小于260℃、銅導體壓接用鍍鎳環形 | Aerospace series - Terminal lugs and in-line splices for crimping on electric conductors - Terminal lugs, ring shaped, nickel plated, for crimping on copper conductors, temperature up to 260 °C for metric and inch stud series - Product standard | |||||||||
| BS EN 3373-012-2005 | 電導體壓接用終端盒和內嵌式接頭.第012部分:溫度小于150℃銅導體壓接用絕緣和密封的內嵌式接頭.產品標準 | Terminal lugs and in-line splices for crimping on electric conductors - Part 012: In-line splices, insulated and sealed, for crimping on copper conductors, temperature up to 150 ℃ - Product standard | |||||||||
| BS EN 3373-013-2005 | 電導體壓接用終端盒和內嵌式接頭.第013部分:溫度小于260℃銅導體壓接用絕緣和防潮的內嵌式接頭.產品標準 | Terminal lugs and in-line splices for crimping on electric conductors - Part 013: In-line splices, insulated and moisture resistant, for crimping on copper conductors, temperature up to 260 ℃ - Product standard | |||||||||
| BS EN 3566-2001 | 航空航天系列.鈦合金8°30'管連接件.帶鎖緊裝置的轉接頭 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Adaptor with lockring | |||||||||
| BS EN 3690-2001 | 航空航天系列.鈦合金8°30'管聯接件.長悶頭活接頭 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Unions, bulkhead, long | |||||||||
| BS EN 3691-2001 | 航空航天系列.鈦合金8°30'管連接件.長焊接的悶頭活接頭 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Unions, bulkhead, long welded | |||||||||
| BS EN 3773-003-1999 | 最大轉換容量為65 In/1000 A，額定電流為1A至25A的溫度補償?shù)膯螛O電路斷路器.米制螺紋接頭.產品標準 | Circuit breakers, single-pole, temperature compensated, rated currents 1 A to 25 A, switching capacity 65 In/1000 A max - Metric thread terminals - Product standard | |||||||||
| BS EN 3773-004-1999 | 最大轉換容量為65 In/1000 A，額定電流為1A至25A的溫度補償?shù)膯螛O電路斷路器.UNC螺紋接頭.產品標準 | Circuit breakers, single-pole, temperature compensated, rated currents 1 A to 25 A, switching capacity 65 In/1000 A max - UNC thread terminals - Product standard | |||||||||
| BS EN 3774-003-1999 | 轉換容量為65 In，額定電流為2A至25A的溫度補償?shù)娜夒娐窋嗦菲?米制螺紋接頭.產品標準 | Circuit breakers, three-pole, temperature compensated, rated currents 2A to 25A, switching capacity 65 In - Metric thread terminals - Product standard | |||||||||
| BS EN 3774-004-1999 | 轉換容量為65 In，額定電流為2A至25A的溫度補償?shù)娜夒娐窋嗦菲?UNC螺紋接頭.產品標準 | Circuit breakers, three-pole, temperature compensated, rated currents 2A to 25A, switching capacity 65 In - UNC thread terminals - Product standard | |||||||||
| BS EN 3852-2002 | 航空航天系列.TI-P64001型鈦合金制、球形、60度管連接器.直螺紋式焊接接頭 | Aerospace series - Pipe couplings, 60 °, spherical, in titanium alloy TI-P64001 - Straight unions, welded, threaded | |||||||||
| BS EN 3853-2002 | 航空航天系列.TI-P64001型鈦合金制、球形、60度管連接器.直活螺紋接頭 | Aerospace series - Pipe couplings, 60 °, spherical, in titanium alloy TI-P64001 - Straight unions, threaded | |||||||||
| BS EN 387-2002 | 膠合層壓板.大指形接頭.性能要求和最低生產要求 | Glued laminated timber - Large finger joints - Performance requirements and minimum production requirements | |||||||||
| BS EN 4031-2001 | 航空航天系列.鈦合金管連接件8°30'.焊接活接頭用螺母 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Nut for welded union | |||||||||
| BS EN 4051-2002 | 航空航天系列.TI-P64001型鈦合金制、球形、60度管連接器.油口接頭 | Aerospace series - Pipe couplings, 60 °, spherical, in titanium alloy - Port connection | |||||||||
| BS EN 4186-2001 | 航空航天系列.鈦合金管連接件8°30'.十字形活接頭 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Unions, cross | |||||||||
| BS EN 4233-2001 | 航空航天系列.鈦合金管連接件8°30'.帶螺紋的焊接活接頭 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Unions, welded, threaded | |||||||||
| BS EN 4552-2003 | 航空航天系列.耐熱鋼制球面37 管聯接器.端部焊接的直管接頭.英制 | Aerospace series - Pipe coupling 37 °, spherical, in heat resisting steel - Straight nipples, welded end - Inch series | |||||||||
| BS EN 4553-2003 | 航空航天系列.耐熱鋼制球面37 管聯接器.端部焊接的90 彎頭管接頭.英制 | Aerospace series - Pipe coupling 37 °, spherical, in heat resisting steel - Elbow 90 ° nipples, welded end - Inch series | |||||||||
| BS EN 4557-2003 | 航空航天系列.耐熱鋼制球面37 管聯接器.端部焊接的T形管接頭.英制 | Aerospace series - Pipe coupling 37 °, spherical, in heat resisting steel - Tees nipples, welded end - Inch series | |||||||||
| BS EN 4610-2005 | 航空航天系列.8°30'鈦合金管接頭.帶推進線螺母的45°彎頭 | Pipe coupling 8°30' in titanium alloy — Elbows 45°, with thrust wire nut | |||||||||
| BS EN 50377-2-1-2001 | 光纖通信系統使用的接頭組件和互連元件.產品規范.接線端設在IEC 60793-2類B1單模纖維上的FC-PC型 | Connectors sets and interconnect components to be used in optical fibre communication systems - Product specifications - Type FC-PC terminated on IEC 60793-2 category B1 singlemode fibre | |||||||||
| BS EN 512-1995 | 纖維水泥制品.壓力管道和接頭 | Fibre-cement products - Pressure pipes and joints | |||||||||
| BS EN 514-2000 | 制作門窗用未增塑聚氯乙烯(PVC-U)型材.膠結角和T接頭的強度測定 | Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors - Determination of the strength of welded corners and T-joints | |||||||||
| BS EN 61284-1998 | 架空線.接頭要求和試驗 | Overhead lines - Requirements and tests for fittings | |||||||||
| BS EN 61300-2-33-2007 | 纖維光學互聯裝置和無源部件.基本試驗和測量程序.試驗.光纜接頭盒組裝和拆卸 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Tests - Assembly and disassembly of fibre optic closures | |||||||||
| BS EN 61466-1-1997 | 標稱電壓超過1000V的架空線用復合絕緣子串組合件.標準強度等級和接頭配件 | Composite string insulator units for overhead lines with a nominal voltage greater than 1 000 V. Standard strength classes and end fittings | |||||||||
| BS EN 639-1995 | 包括接頭和配件的混凝土壓力管的共同要求 | Common requirements for concrete pressure pipes including joints and fittings | |||||||||
| BS EN 640-1995 | 鋼筋混凝土壓力管和分布鋼筋混凝土壓力管（非圓柱型），包括接頭和配件 | Reinforced concrete pressure pipes and distributed reinforcement concrete pressure pipes (non-cylinder type), including joints and fittings | |||||||||
| BS EN 641-1995 | 包括接頭和配件的圓柱型加筋混凝土壓力管 | Reinforced concrete pressure pipes, cylinder type, including joints and fittings | |||||||||
| BS EN 642-1995 | 包括接頭、配件和管道預應力鋼特殊要求的圓柱型和非圓柱型預應力混凝土壓力管 | Prestressed concrete pressure pipes, cylinder and non-cylinder, including joints, fittings and specific requirement for prestressing steel for pipes | |||||||||
| BS EN 715-1995 | 熱塑管道系統.小直徑壓力管和配件間端部負荷軸承接頭.在包含端推力的內部水壓下密封性的試驗方法 | Thermoplastics piping systems - End-load-bearing joints between small diameter pressure pipes and fittings - Test method for leaktightness under internal water pressure, including end thrust | |||||||||
| BS EN 751-1-1997 | 與第1,2,3類家庭用燃氣和熱水裝置連接的金屬螺紋接頭的密封材料.厭氧密封劑 | Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Anaerobic jointing compounds | |||||||||
| BS EN 751-2-1997 | 與第1,2,3類家庭用燃氣和熱水裝置連接的金屬螺紋接頭的密封材料.非硬化密封劑 | Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Non-hardening jointing compounds | |||||||||
| BS EN 751-3-1997 | 第1,2,3類家庭用燃氣和熱水裝置連接的金屬螺紋接頭的密封材料.非燒結PTFE密封帶. | Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Unsintered PTFE tapes | |||||||||
| BS EN 804-1995 | 塑料管道系統.壓力管道溶劑膠粘接頭的注射模塑承口連接管件.短期內部液壓壓力的試驗方法 | Plastics piping systems - Injection-moulded socket fittings for solvent-cemented joints for pressure piping - Test method for resistance to a short-term internal hydrostatic pressure | |||||||||
| BS EN 846-3-2000 | 圬工輔助砌塊的試驗方法.預制基地加固處接頭的剪切負載容量的測定 | Methods of test for ancillary components for masonry - Determination of shear load capacity of welds in prefabricated bed joint reinforcement | |||||||||
| BS EN 877-1999+A1-2006 | 建筑物中水排放用生鐵管和配件及其接頭和配件.要求、試驗方法和質量保證 | Cast iron pipes and fittings, their joints and accessories for the evacuation of water from buildings — Requirements, test methods and quality assurance | |||||||||
| BS EN 911-1996 | 塑料管道系統.熱塑塑料壓力管道用的彈性密封環型接頭和機械接頭.外部流體靜壓條件下防漏密封試驗方法 | Plastics piping systems - Elastomeric sealing ring type joints and mechanical joints for thermoplastics pressure piping - Test method for leaktightness under external hydrostatic pressure | |||||||||
| BS EN ISO 10042-2006 | 焊接.鋁和鋁合金弧焊接頭.缺陷質量分級 | Welding - Arc-welded joints in aluminium and its alloys - Quality levels for imperfections | |||||||||
| BS EN ISO 10692-2-2001 | 氣瓶.用于微電子工業的儲氣瓶閥的連接接頭.接到鋼瓶連接接頭上的閥門的定型試驗和規范 | Gas cylinders - Gas cylinder valve connections for use in the microelectronics industry - Specification and type testing for valve to cylinder connections | |||||||||
| BS EN ISO 11144-1997 | 牙科設備.漱口沖洗牙用給排水管接頭 | Dental equipment - Connections for supply and waste lines | |||||||||
| BS EN ISO 13844-2000 | 塑料管道系統.與未增塑聚氯乙烯管一起使用的未增塑聚氯乙烯彈性密封環式套筒接頭.負壓下的密封性試驗方法 | Plastics piping systems - Elastomeric-sealing-ring-type socket joints of unplasticized poly(vinyl chloride) (PVC-U) for use with PVC-U pipes - Test method for leaktightness under negative pressure | |||||||||
| BS EN ISO 13845-2000 | 塑料管道系統.與未增塑聚氯乙烯管一起使用的彈性密封環式套筒接頭.內壓下角度偏轉密封試驗 | Plastics piping systems - Elastomeric-sealing-ring-type socket joints for use with unplasticized poly(vinyl chloride) (PVC-U) pipes - Test method for leaktightness under internal pressure and with angular deflection | |||||||||
| BS EN ISO 13846-2001 | 塑料管道系統.熱塑性壓力管用端負載和無端負載支承組件和接頭.內部水壓下長期密封性的試驗方法 | Plastics piping systems - End-load-bearing and non-end-load bearing assemblies and joints for thermoplastics pressure piping - Test method for long-term leaktightness under internal water pressure | |||||||||
| BS EN ISO 13919-1-1997 | 焊接.電子和激光束焊接接頭.缺陷的質量級別導則.鋼 | Welding - Electron and laser beam welded joints - Guidance on quality levels for imperfections - Steel | |||||||||
| BS EN ISO 13919-2-2001 | 焊接.電子和激光束焊接接頭.缺陷的質量分級指南.鋁及其可焊合金 | Welding - Electron and laser beam welded joints - Guidance on quality levels for imperfections - Aluminium and its weldable alloys | |||||||||
| BS EN ISO 14324-2003 | 電阻點焊.焊接有損試驗.點焊接頭的疲勞試驗方法 | Resistance spot welding - Destructive tests of welds - Method for the fatigue testing of spot welded joints | |||||||||
| BS EN ISO 15236-4-2004 | 鋼絲繩運輸帶.硫化的帶接頭 | Steel cord conveyor belts - Vulcanized belt joints | |||||||||
| BS EN ISO 15245-1-2001 | 氣瓶.連接儲氣瓶閥門接頭用平行螺紋.規范 | Gas cylinders - Parallel threads for connection of valves to gas cylinders - Specification | |||||||||
| BS EN ISO 16070-2006 | 石油和天然氣工業.下降孔設備.鎖緊芯軸和落地螺紋接頭 | Petroleum and natural gas industries - Downhole equipment - Lock mandrels and landing nipples | |||||||||
| BS EN ISO 17659-2004 | 焊接.帶圖解的焊接接頭的多語種術語 | Welding - Multilingual terms for welded joints with illustrations | |||||||||
| BS EN ISO 22825-2006 | 接頭的無損檢驗.超聲波試驗.奧氏體鋼和鎳基合金接頭的試驗 | Non-destructive testing of welds - Ultrasonic testing - Testing of welds in austenitic steels and nickel-based alloys | |||||||||
| BS EN ISO 4797-2005 | 實驗室玻璃器皿.錐形磨口接頭燒瓶 | Laboratory glassware - Boiling flasks with conical ground joints | |||||||||
| BS EN ISO 5356-1-2004 | 麻醉和呼吸設備.圓錐形接頭.錐體和錐套 | Anaesthetic and respiratory equipment - Conical connectors - Cones and sockets | |||||||||
| BS EN ISO 5620-1-1997 | 造船和海上建筑物.飲用水箱注水接頭.總要求 | Shipbuilding and marine structures - Filling connection for drinking water tanks - General requirements | |||||||||
| BS EN ISO 5620-2-1997 | 造船和海上建筑物.飲用水箱注水接頭.部件 |
Shipbuilding and mar欄目導航新聞中心
聯系我們CONTACT US聯系人：彭工 手機：18918462396 電話：021-59718851 地址： 上海市青浦區青浦工業園清河灣路819弄 | |||||||||
KUNAG
KUNAG
KUNAGE